Mouse Test
Press every button and roll the wheel inside the test area. Each part lights up when it works.
Best tested with a mouse on desktop.
Test area
On this page5 sections ▾
The Mouse Test checks whether every part of your mouse works. Press each button inside the test area: left, right, middle, back and forward. Then roll the scroll wheel both ways. Each part lights up when it registers, and the test warns you if it spots an unwanted double-click.
What Does the Mouse Test Check?
The test covers every input a standard mouse has, plus the most common fault:
| Part | What the test checks |
|---|---|
| Left button | Each click registers, and only once. |
| Right button | Each click registers. The usual right-click menu is blocked inside the test area so you can test freely. |
| Middle button | Pressing the scroll wheel down works as a click. |
| Back and forward buttons | The two side buttons work. These are common on gaming mice. |
| Scroll wheel | Up and down scrolls are each counted separately. |
| Double-click detection | Two left clicks less than 80 ms apart are flagged as a possible fault. |
Everything you press is listed in the event log, with the time it happened, so you can see exactly what your mouse sent.
How to Test Your Mouse: Step by Step
- Step 1: Move your pointer into the test area. Buttons only register while the pointer is inside it.
- Step 2: Click each button one at a time. Press left, right, middle, back and forward, and check that the matching part of the mouse picture lights up.
- Step 3: Check the counters. Each button’s count should go up by exactly one per press. A jump of two from one press points to a double-click fault.
- Step 4: Roll the scroll wheel. Scroll slowly up, then down, and make sure each direction is counted correctly.
- Step 5: Test the left button for double-clicks. Click it normally 20–30 times. If the test shows a double-click warning, your switch may be wearing out.
- Step 6: Press Reset and repeat. Running the test twice confirms whether a problem is real or a one-off.
How to Spot a Double-Click Problem
A double-click problem happens when one press of the button registers as two clicks. It’s one of the most common mouse faults, and it usually comes from a worn or dirty switch inside the button. Instead of closing cleanly, the switch’s contacts bounce and send an extra click.
How our test catches it: when two left clicks arrive less than 80 ms apart, the test flags a possible double-click. That’s faster than most people click on purpose, so it usually points to the switch, not your finger.
Click normally during this check. Fast techniques like butterfly clicking can produce gaps under 80 ms on their own and trigger a false warning.
If you see the warning:
- Retest a few times to confirm it keeps happening.
- Clean around the button with a short burst of compressed air.
- Raise the debounce time in your mouse software, if it has that setting.
- Check your warranty. A failing switch is often covered.
Button Not Working? Common Causes and Fixes
If a part of your mouse doesn’t light up in the test, start with these common causes:
| Problem | Likely cause | Try this |
|---|---|---|
| Nothing registers at all | The pointer is outside the test area, or the mouse has lost connection. | Move the pointer into the area, then try another USB port or new batteries. |
| Side buttons don’t register | Your mouse software has remapped them to keyboard shortcuts. | Reset the button settings in your mouse software. |
| Left and right are swapped | Your system’s left-handed setting is turned on. | Check the primary button setting in your operating system. |
| Clicks arrive late or get missed | A weak wireless signal or a low battery. | Move the receiver closer, or charge the mouse. |
| Works here, but not in a game | The button isn’t bound to an action in the game. | Check the game’s control settings. |
| Middle click doesn’t register | A stiff or worn wheel switch. | Press firmly in the centre of the wheel. If it still fails, the switch may need repair. |
Mouse Test FAQ
How do I know if my mouse is double-clicking?
Click the left button normally inside the test area 20–30 times. If one press increases the count by two, or the test shows a double-click warning, your switch is likely faulty.
Why don’t my mouse side buttons work?
Usually your mouse software has remapped them to other actions, or a driver is missing. Reset the button settings in your mouse software, then test them again here.
Can I test my mouse on a laptop touchpad?
Yes. Taps and clicks on a touchpad count as left clicks, and two-finger clicks usually count as right clicks. Most touchpads have no middle or side buttons to test.
Does the Mouse Test work with wireless mice?
Yes, it works with wired, wireless and Bluetooth mice. If clicks arrive late or go missing, charge the mouse or move its receiver closer, then test again.